HP 3325A SERVICE MANUAL PDF

View and Download HP A calibration manual online. Synthesizer/Function Synthesizer HP A Operating And Service Manual. Frequency ( pages) . The Operating and Service Manual contains inforĀ¬ mation required to install, operate, test, adjust, and servĀ¬ ice the Hewlett-Packard Model A. Find great deals for HP a Function Generator Operating and Service Manual . Shop with confidence on eBay!.

Author: Tojataur Akigis
Country: United Arab Emirates
Language: English (Spanish)
Genre: Literature
Published (Last): 9 October 2004
Pages: 280
PDF File Size: 4.41 Mb
ePub File Size: 6.4 Mb
ISBN: 549-8-21837-550-8
Downloads: 91846
Price: Free* [*Free Regsitration Required]
Uploader: Taulabar

Adjust the counter to measure frequency 20 MHze. The system controller may designate itself as either talker or listener.

However, if one chooses to modify the newer board to use the older connectors and cablesW36 sefvice required. Table lists parts in alphanumeric order of their reference designators and indicates the description, -hp- part, number of each part, together with any applicable notes, and provides the following: Press A High Voltage Output key lower right corner of front panel. In this mode, each device dependent character byte is processed when received.

Triangle and Ramp Linearity Test. In each case, allow the thermal converter serice seconds to stabilize.

Change A frequency to Do Manuzl use a Equipment required to maintain the Model A is listed in Table The universal unlisten command removes all listeners from the bus, allowing only the listencr s designated by the device s listen parameter to receive information. Model A Operation 3. For ease of recording data at various times, copies of the blank Performance Test Record may be made without written permission from Hewlett-Packard.

  KATHERINE ANNE PORTER THE JILTING OF GRANNY WEATHERALL PDF

This connector is Part No. Sine 40 V 4 mV Hewlett-Packard uses a two-section serial number consisting of a four-digit prefix and a five-digit suffix.

Set the analyzer controls as follows: When connected to a ohm coaxial cable that is terminated by a 50 ohm resistive load, the sync signal levels are as follows: Connect an ac digital voltmeter to the A signal output. Replace the lOVp-p pad with the 3.

This procedure is for instruments with the Option High Stability frequency Reference. See Service Group C.

HP 3325a Function Generator Operating and Service Manual

Set A frequency to Hz, 1 kHz, and kHz and read ac voltage. Change A frequency to kHz and function to square.

The AC voltmeter reading should be By Order of the Secretary of the Army: Change the A frequency to kHz. The following front pane! All spurious non-harmonic signals should be at least 70dB below the fundamental. The A does not respond to Parallel Poll. Instruments in this serial number range do not have CRI09 or R These instruments do not have C Set A to square wave and read positive peak on DC voltmeter.

After receiving an interrogation, the A will send back the following the next time it is addressed to talk: Change oscilloscope delay to and read negative peak. Verify that ramp period variations do not exceed ten divisions. Instrument specifications are listed in Table I-I, These specifications are the performance standards or limits against which the instrument is tested.

  AL-QADIM 3.5 PDF

The instructions outlined in paragraphs 6 and 7 are preparatory to the calibration process. Set the digital voltmeter to measure dc voltage. Move the counter input to the sync output of the A. Line 5 Return to Line 1 to continue sweeping. The log indicator should light. Connect A signal output to CRO and voltage divider via a 6 ft.

Set the A frequency to 5. Page 22 TB Figure 5. IV p-p DC Offset.

HP a Function Generator Operating and Service Manual | eBay

This procedure checks the voltage levels of the sync output square wave: Connect an ac digital voltmeter to the A signal output via a 50 ohm feedthru termination. The HP-IB is a parallel bus of 16 active signal lines grouped into three sets according to function, to interconnect up to 15 instruments.

This information may be found on the rear panel. Thsi is not a User Manual. Set the oscilloscope controls as follows: The data lines carry coded messages which represent addresses, program data, measurements, and status bytes. The status information byte 8 bits sent by the device will tell whether that device needed service hpp why. Enter 20 MHz in the A. Low at start of sweep, High at stop.

iPhone X