GE VAT2000 PDF

Ge VAT Pdf User Manuals. View online or download Ge VAT Instruction Manual. View and Download GE VAT instruction manual online. AC SPEED CONTROL EQUIPMENT. VAT Controller pdf manual download. GE’s distributor or our sales representatives who will be willing to help you. Please keep GE’s inverters are all passed the function test before delivery. Please.

Author: Kizshura Arashisho
Country: Luxembourg
Language: English (Spanish)
Genre: Spiritual
Published (Last): 17 April 2017
Pages: 284
PDF File Size: 19.52 Mb
ePub File Size: 13.75 Mb
ISBN: 938-3-87172-669-1
Downloads: 23988
Price: Free* [*Free Regsitration Required]
Uploader: Kale

Control mode change- Select control at speed detection error over during speed Page of Go.

Drive Parameter gw mode: B Torque bias 1 setting Refer to section for details on selecting the torque bias 1 setting. Customising Block-b,c Parameter Chapter 7 Options 7.

Increase the deceleration time setting A Unit Function value value value C22 – Overload The C, 2 data will be Overload setting limited by this value when this Constant torque Sensor Vector Control Reference: IO-n sub-code Gate Shutdown Circuit error.

Control Functions and Parameter Settings B Torque setting Refer to section for details on selecting the torque setting. Read this manual thoroughly before using the VAT, and store in a safe place for reference. Chapter 8 Maintenance And Inspection Sequence Input Logic Reading Fault History 4. Control Functions and Parameter Settings C Overspeed protection level This parameter set the overspeed protection level, as a percentage in respect to the maximum frequency B or maximum speed B Test Operation and Adjustment 8 Move the digit with the key, and using the knob, raise the frequency to 50Hz.

  DAI SIJIE BALZAC Y LA JOVEN COSTURERA CHINA PDF

This setting value is the lower limit of Phase conductors only pass through output ferrite ring, Not earth conductor p It is important that the lead length from filter to inverter and unscreened length of motor output cable be kept as short as possible.

VAT2000 AC Drive Series VAT 2000 GE Power Controls

A short circuit in the load may have occurred. Frequency speed setting input A: Troubleshooting With Fault Display Use a shielded wire shorter than 30m for the wiring. The mode or block displayed will change each time when the key is pressed.

Maximum overload allowed in VT: Parameters B basic functions Control Functions and Parameter Settings C Pick-up wait time The wait time t is a safety delay to ensure that the pick-up operation is enabled a time after the output is cut off, once the motor residual voltage is disappeared. Note 7 An output voltage exceeding the input voltage cannot be attained.

VAT2000-U2KX07K5S

Stop Frequency speed Page 3 Refer to section 1 and set the parameters B to 3. When using the 2-phase pulse, the rotation direction is judged by the advance and delay of the 2-phase pulse. The motor increases or decreases its speed according currently valid ramp rate.

Is possible to set the number of retries, and the wait time t. The output frequency speed changes immediately according to the operation. A trouble may have occurred in the cooling fan.

VAT GE Power Control AC Speed Control VATU2KX07K5s

Freque ncy B 0 Rest of the World Day estimated shipment. Bias B, 4 where B” Changing Of Terminal Functions 5. ON without pick-up If the run command is ON at the power ON time, then vat200 drive will start once the pre- charging is completed. The operation of the VAT must be checked every six months by turning the power on. Setting Setting data Explanation input point Serial In this case, the signal command RUN-R. The sequence input Vaf2000 has been activated.

  LONE SURVIVOR BY MARCUS LUTTRELL AND PATRICK ROBINSON PDF

AC Speed Drive Inverter VATU2KNS GE VATU2KNS *Used* | eBay

IP54 detachable keypad, door mountable, Keypad includes drive operation keys Forward, Reverse and Stop Parameter operation keys eg Mode keys. Page 48 Page 49 – Reading the changed parameters Non-defa Preparation For Operation Page 81 This will affect the current response. Programmable Sequence Output Function pso 5. Flow Of Test Operation One of the two types of inputs can be selected by setting a parameter or with the sequence input.

Test Operation With Operation Panel The wire length must be 30m or less. This website uses cookies. VAT O pe n collecto r M ax. Test Operation and Adjustment 2 Automatic tuning operation procedures The automatic tuning is carried out according the following procedure.

They must be replaced periodically.

iPhone X