Instruction manual • Read online or download PDF • Futaba 12Z User Manual. Futaba 12Z User Manual • Motor • Futaba Accessories communication. Read online or download PDF • Page / • Futaba 12Z User Manual • Futaba Accessories communication.
|Published (Last):||19 August 2014|
|PDF File Size:||15.52 Mb|
|ePub File Size:||19.76 Mb|
|Price:||Free* [*Free Regsitration Required]|
Comments to this Manuals Your Name.
Function, Functions of linkage menu, Function change – Futaba 12Z User Manual
If a target time is set and the timer reaches the set The timers are stored independently with each model, time, a buzzer sound for each count is generated. Page 14 Volume Digital trim This transmitter is equipped with digital trims. When the aileron stick is manipulated, the ailerons and camber flaps perform aileron operation simultaneously and the operation characteristic of the roll axis is improved. Use the Function menu of the Linkage Menu to assign the sensitivity is used to stabilize the aircraft’s attitude.
Before Use T12Z is operated by 7. The method of applying the curve setup screen, and then correct the sinking. After once operating the cursor lever to button.
Seven types of main wings and three types of tail wings are available for gliders. T12Z is operated by 7.
FUTABA 12Z SERIES INSTRUCTION MANUAL Pdf Download.
Complain wrong Brand wrong Model non readable. We recommend sending your system to the Futaba Service Center annually during your non-flying season for a complete checkup and service. The last condition becomes the you want to change of the condition name, highest priority. Trim mix function call can be linked to a stick, For a description of the setting method, see The channel assignment initial setting for each model type is shown below.
A typical menu screen is shown selection, frequency setting, end point setting, and below. Setting of these 2 positions can be selected by switch. Use the cursor lever to move the cursor reverse-display to the [POINT] item and turn the data input dial to the left or right and select the point whose rate you want Up to 17 curve the setup screen shown below by pushing the Currently selected condition name enter button.
If you later change model commands that apply to helicopters only. In addition, when the trim position returns to the center, the tone will change. You can freely change combinations between functions aileron, elevator, etc and input controllers sticks, switches, trim levers and trim switches.
The action is not functional at high throttle to avoid accidental dead sticks.
For PPM mode, you can set only eight linear channels. Page 53 Manal type Select the model type f r o m a m o n g a i r p l a n ehelicopter, glider, and motor glider.
Swash Mix SWASH MIX Futwba of use The swash mix function is used to correct the swash plate in the aileron roll direction and elevator cyclic pitch corresponding to each maanual tendencies in the roll direction operation of each condition.
SWASH MIX Example of use The tutaba mix function is used to correct the swash plate in the aileron roll direction and elevator cyclic pitch corresponding to each undesirable tendencies in the roll direction operation of each condition.
Normally, it is used with the high side and low side trim function. All programming and setup may be done in this manner without transmitting. Page Updating following procedure to update the program. Use this function when you want to suppress the torque generated by the changes in the pitch and speed of the main rotor during pitch operation. Page 70 Flight condition’s addition, deletion, copy, condition renaming, and condition delay can be set.
Motor | Futaba 12Z User Manual | Page /
When you select model and wing swash types. The T12Z is designed so that the airplane Before setting the model data, use the Model and glider including EP glider model types are Type function of the Linkage Menu to select the Mixing applied in other swash modes is different, but the setting procedure is the same.
The winglet is a vertical or angled extension at the tips of each wing. Page 43 Receiver and servo connection Connect the receiver and servos in accordance with the connection diagram shown below.
Got it, continue to print. We immediately began to evaluate the backlog of Futaba parts and service requests, completing what could be done with available parts. For a description of the switch setting method, see the description at the back of this manual.
In order for you to make the best use of your system and to fly safely, please read this manual carefully. Page 24 is displayed and the frequency data is sent to the receiver 5. SUB-TRIM The Sub-Trim function is used to set the servo neutral position, and may be used to make fine adjustments to the control surface after linkages and pushrods are hooked up.
Setting method tuned mamual changes in rotor speed accompanying conditions. Don’t show me this message again. You may individually except Condition Select. When to PPM mode.
Page 57 SUB-TRIM The Sub-Trim function is used to set the servo neutral position, and may be used to make fine adjustments to the control surface after linkages and pushrods are hooked up.
Page 71 condition whose priority you want to change in the condition list. Starts and sets the trainer system. Also Split Time may be counted. For retail sales of Futaba, please visit your local dealer or Tower Hobbies.
Seven swash types are available for helicopters.
Refer to it when setting each function. Be very careful flying in areas near power lines, tall buildings, or communication facilities as there may be radio interference in their vicinity. The operation speed can be set in 2 ranges of slow speed flight and high speed operated as a safety function by setting 2 switches. We hope we will fitaba the opportunity to provide you with nanual products and outstanding customer service in the future.