FRENIC-Lift. FRENICG11S/P11S. FRENICVG7S. User’s Manuals and Technical Information. FRENIC-Multi User’s Manual. FRENIC-Eco User’s. FRENIC-Lift is an inverter designed to drive a three-phase induction motor ( hereafter For details about this product, refer to the FRENIC-Lift User’s Manual that. The FRENIC-Lift Series of exclusive AC Drives for operation of elevators are FRENIC-Lift AC Drives are available in a series with capacities ranging from

Author: Kajizil Memi
Country: Montserrat
Language: English (Spanish)
Genre: Career
Published (Last): 4 February 2007
Pages: 401
PDF File Size: 18.74 Mb
ePub File Size: 10.65 Mb
ISBN: 187-5-96446-475-6
Downloads: 77305
Price: Free* [*Free Regsitration Required]
Uploader: Goltilabar

Page 61 L codes: Retry during the period specified by timer y Page 40 Table 2. Page 25 Terminal board illustrated in except Figure A. Wiring For Control Circuit Terminals 2. For manua, refer to [X2] Digital Chapter 5, Section 5. Chapter 6 Troubleshooting 1 First, check that the inverter is correctly wired, referring to Chapter 2, Section 2. Icons The following icons are used throughout this manual. Page 35 Table 2. Frenkc any of the problems listed below occur, take an appropriate measure against them.

Refer to Chapter 2 Section 2. Torque bias gain liff BTBG. Page Fuji Electric Co. When employing external cooling At the shipment time, the inverter is set up for mount inside your equipment or enclosure so that cooling is done all internally. Speed monitor Select by E48 3: U, V and W respectively and that the grounding wires are connected to the ground electrodes correctly.

It is recommended that the following parts be maanual as specified below. Do not use a circuit breaker with a capacity exceeding the recommended capacity.


Fuji Electric FRENIC-Lift series Instruction Manual

Refer to Figure 2. Init ialize all function code data to t he factory defaults H04 Auto-resetting 0: Don’t show me this message again. Comments to this Manuals Your Name. Don’t have an account? Driving gener- When high starting torque is required or quick acceleration or deceleration al-purpose motor Selecting is required, select an inverter with a capacity one size greater than the inverter standard. Megger test of main circuit Use a VDC Megger and shut off the main power supply without fail during measurement.

Precautions For Use Precautions for use Driving a V When driving a V general-purpose motor with an inverter using ex- general-purpose tremely frenoc wires, damage to the insulation of the motor may occur. For the motor, check the rated values printed on the nameplate of the motor. Accident or injury may result. Do not hold covers or individual parts only.

Setting Up Slide Switches 2. Page 37 Table 2. How This Manual Is Organized This chapter lists specifications including output ratings, control system, external dimensions and protective functions. The first letter is an alphabet that identifies its group and the following two letters are numerals that identify each individual code in the group.


Page 77 [ 16 ] Run operation error Problem You incorrectly operated the inverter. Attachment for This adapter allows you to mount your FRENIC-Lift series lkft inverters on the panel in such a external cooling way that the heat sink assembly may be exposed to the outside.


Put the front cover back in reverse order of.

Torque limit level is F The 1st week of January is indicated as ’01’. Page 24 – Freinc arrangement and screw specifica Doing so could cause burns. Lighten the load or change the inverter for an upper size. Brake control by time 2: Tuning procedure What follows gives you a tuning procedure of the inverter for a motor using a multi-function keypad option. Possible Causes What to Check and Suggested Measures 1 A high intensity noise was Check if appropriate noise control measures have been implemented e.

When the replacement is necessary, contact your Fuji Electric representative. Three-phase v series, three-phase v series, single-phase v series 6 pages. Page 41 Table 2. Otherwise injuries could occur. This chapter lists specifications including output ratings, control system, external dimensions and protective functions. In no event will Fuji Electric Co. The two terminals prepared for grounding, which are indicated by the symbol G in Figures A to C, make no distinction between mnual power supply side primary circuit and the motor side secondary circuit.


To use it follow the steps listed below.

iPhone X