AN datasheet, AN circuit, AN data sheet: PANASONIC – 5-Dot LED Driver Circuit,alldatasheet, datasheet, Datasheet search site for Electronic. AN datasheet, AN pdf, AN data sheet, datasheet, data sheet, pdf, Panasonic, 5-Dot LED Driver Circuit. Description, 5-dot Led Driver Circuit. Company, Panasonic Industrial Company/ Electronic Components. Datasheet, Download AN datasheet. Cross ref.

Author: Dugami Gardazilkree
Country: Russian Federation
Language: English (Spanish)
Genre: Automotive
Published (Last): 1 April 2017
Pages: 363
PDF File Size: 15.32 Mb
ePub File Size: 1.43 Mb
ISBN: 756-2-24204-995-7
Downloads: 55585
Price: Free* [*Free Regsitration Required]
Uploader: Akinotaur

Passing Vin through a reverse capacitor seems to be potentially more prone to failure. Most people use “low” to refer to either a lower voltage, or a lower position on the diagram. This circuit will datasgeet the LEDs as the input voltage on pin 8 increases relative to pin 7.

Have you tried a non-polarized capacitor e. Can someone explain what the reversed capacitor is doing here? I know the correct names, but I conversely find “inverting” and “noninverting” confusing when dealing with comparators, since those terms make more adtasheet when dealing with op-amps.

Very confusing terminology, since the inverting input can have a higher an8684 than the noninverting input. Reverse biased capacitor on IC input pin Ask Question. Vref is the high side of the 5 LED comparators in the datasheet block diagram.

Setting 7 higher than ground biases the low side of the comparators, allowing them to turn on with a lower output from the amp. There is also xn6884 discharge path with your arrangement. How does doing anything to pin 7 or pin 8 affect that? That’s clear, because the input in my test circuit is DC.

By using our site, you acknowledge that you have read and understand our Cookie PolicyPrivacy Policyand our Terms of Service. Post Your Answer Discard By clicking “Post Your Answer”, you acknowledge that you have read our updated terms of serviceprivacy policy and cookie policyand that datzsheet continued use of the website is subject to these policies.


You should fix the capitalisation of sentences and electrical units ‘F’ for farad to improve legibility and credibility. I’m not following you. Email Required, but never shown. It sounds like you’re trying to drive this circuit with a signal that includes a considerable DC bias, which explains why all of the LEDs light up right away when you remove short out the capacitor.

(Datasheet) AN pdf – 5-Dot LED Driver Circuit (1-page)

It just shortens the range of turn over which the potentiometer works. That means there is a small current flow out from the pin. Pin 7 is the output of the internal amplifier, and pin 8 is its input, designed to accept a low-level AC input 57 mV for a 0-dB indication. If I “correct” the orientation, the circuit does not work at all. Post as a guest Name. Your description doesn’t agree with that in the datasheet. The potentiometer is clear, but the 2.

Pin 8 is the signal input fatasheet, and it’s the internal Op amp’s positive input. The LED pins connect to the negative side of an68884 LEDs, and the pins go low when the output of the internal amp goes above Vref dropped by voltage dividing resistors at each comparator.

This makes sense, but why not a diode? I’m not reading it that way. However, if that’s the case, I can’t explain why reversing the capacitor doesn’t work, unless the actual polarity of the capacitor is backwards from what you think it is.

AN6884 Datasheet

Indeed, it must in order for any of the LEDs to turn on! To be clear, removing the capacitor doesn’t light up the LEDs all at once. Placing it at a higher voltage within the datasheet’s max specified V will both lower the amplification and raise the lower rail of the comparators in the block diagram. It appears to be reversed. Per AN’d datasheet. You might want to edit to explain your answer a bit more.


Home Questions Tags Users Unanswered. Sign up or log in Sign up using Google. As displayed, the LEDs go from fully off to fully on over roughly the entire turn range of the potentiometer. By clicking “Post Your Answer”, you acknowledge that you have read our updated terms of serviceprivacy policy and cookie policyand that your continued use of the website is subject to these policies.

The diode will mess up the response of the chip due to its forward voltage drop. It’s the DC bias determine the polarity.

(PDF) AN6884 Datasheet download

That is to say that the LEDs all zn6884 on at a much smaller turn of the potentiometer. I will be certain to use them here from now on.

By “low side”, you’re referring to the inverting inputs of the comparators. If I remove the 2. I am looking at the test circuits on the data sheet for the AN VU meter IC, and I cannot understand the connection to pin 8 in the following diagram: Right, I get that pin 7 is the output of the amp, but it’s part of the negative feedback loop on the amp.

There’s still a much shorter range over which a varying number of LEDs come on. Capacitor with polarity can be used ac daatsheet or blocking. Per AN’d datasheetPin 8 is the signal input pin, and it’s the internal Op amp’s positive input. Sign up using Email and Password.

iPhone X