Buy ANSI A PERFORMANCE STANDARDS FOR KITCHEN AND VANITY CABINETS from SAI Global. Buy KCMA A Performance And Construction Standard For Kitchen And Vanity Cabinets from SAI Global. Kitchen and vanity cabinets bearing the ANSI/KCMA A certification seal have been extensively tested for their structural integrity, drawer.

Author: Zulur Maukora
Country: Nepal
Language: English (Spanish)
Genre: Automotive
Published (Last): 18 December 2011
Pages: 493
PDF File Size: 3.4 Mb
ePub File Size: 11.91 Mb
ISBN: 960-5-90876-531-5
Downloads: 49870
Price: Free* [*Free Regsitration Required]
Uploader: Karr

Shelves and bottoms are ansj at 15 pounds per square foot to ensure no excessive deflection or joint failure on the cabinet or mounting system.

The maximum number of products that can be compared is 4. Share your thoughts with us in the comments below. The finish must then show no appreciable discoloration and no evidence of blistering, cold checking, or other film failure.

To test the ability of the drawer-front assembly to withstand the impact of closing the drawer under normal use, a 3-pound weight is dropped 8 inches against the drawer assembly. The cycle is repeated five times.

View the discussion thread.

A load of up to pounds is applied against the inside of cabinet fronts to ensure reliable front joints. In order to be certified, cabinets must also undergo eight categories of testing, covering structural integrity, drawer and door operation and finish quality see sidebar below.

Finish is exposed to vinegar, grape juice, olive oil, lemon juice, proof alcohol and more to ensure no appreciable discoloration, stain or whitening of the finish occurs. The exceptions are sink fronts and bases, oven cabinets and refrigerator cabinets. The door must remain weighted for 10 minutes, after which the door and hinges must show no visible signs of damage, and connections between cabinet-and-hinge and door-and-hinge must show no sign of looseness.


For information on the certification or to locate a certified cabinet manufacturer, visit the Certifications portal at KCMA. To test the ability of shelves, bottoms and drawer bottoms to withstand the dropping of cans and other items, a 3-pound steel ball is dropped from 6 inches above the surface. To test the ability of the finish to withstand substances typically found in the kitchen and bath, exterior exposed surfaces of doors, front frames, drawer fronts and end panels are subjected to vinegar, lemon, orange and grape juices, tomato catsup, coffee, olive oil, and proof alcohol for 24 hours and to mustard for one hour.

A11.1 ensures the cabinets will live up to your expectations. A 3 pound weight is dropped 10 times against the drawer assembly to ensure that the drawer front assembly will withstand the impact of closing.

A 3 pound steel ball is “drop tested” against shelves, cabinet bottoms and drawer bodies to ensure cabinets will withstand dropping of cans and other items.

Mastercraft Cabinets | KCMA Certification Program, ANSI Standards

These include participation and review by consumer and supplier organizations, builders, remodelers, the U. Cabinet finishes are inspected to ensure that stringent standards of appearance are also met.

On all cabinets, the shelves and bottoms are loaded at 15 pounds per square foot, with the weight maintained for seven days to ensure that there is no excessive deflection and no visible sign of joint separation or failure of any part of the cabinets or the mounting system. Your Email has been successfully sent! The door edge must then show no delamination or swelling and no appreciable discoloration or evidence of blistering, checking, whitening, or other film failure. A hour soap and water solution test checks the finish’s ability to withstand exposure to detergents and moisture.


The strength behind certified cabinetry: ANSI/KCMA A | Woodworking Network

To be certified, cabinetry must first meet the following 14 construction requirements: Your recommendation is being sent! Scroll Down for more stories. After the test the drawer must not be damaged and must operate as before the test, with no visible sign of joint separation or failure of any part of the cabinet or mounting system. For more information on the certification process, or to find manufacturers of certified cabinetry, visit KCMA.

The strength behind certified cabinetry: ANSI/KCMA A161.1

To test the ability of doors, door-holding devices, hinges and attachment devices to operate under the anssi of normal use, doors are opened and closed through a full degree swing for 25, cycles. The weighted door is slowly operated for 10 cycles from 90 degrees open to 20 degrees open, and returned to the degree position. Please refine your selection.

Welcome to our redesigned homepage! Cabinets are impact tested by striking the z161.1 of a closed and open door with a 10 pound sand bag. Skip to main content.

iPhone X