BRYSTON OWNER’S MANUAL Instructions For Bryston SST Series Amplifiers Models 3B SST and 4B SST 3B SST and 4B SST Series Amplifiers Table of. Audio manuals and audio service pdf instructions. Find the user manual you need for Bryston 4B SST Stereo Amplifier User Manual. Page 1. Page 2. Page 3. User guide • Read online or download PDF • Bryston 4BSST User Manual • Bryston Receivers and Amplifiers.
|Genre:||Health and Food|
|Published (Last):||10 February 2006|
|PDF File Size:||7.80 Mb|
|ePub File Size:||4.20 Mb|
|Price:||Free* [*Free Regsitration Required]|
This warranty gives you specific legal rights and you may also sts other rights which may vary from province to province and country to country.
Bryston will custom build cables for your application. Any SST channels thermally shutting down during operation indicates insufficient air flow, and a remedy must be found for cooling the amplifier. Use paired wire of 22 to 18 gage sufficient in length between the source device and the SST amplifier.
Each channel selects a balanced or single ended input.
Heat Dissipation 8 ohms – Bridged Ss 8 ohms Max. This includes parts, labour and return shipping to the first owner and all subsequent owners. In the event of a defect or malfunction, Bryston will remedy the problem by repair or replacement, as we deem necessary, to restore the product to full performance.
Bryston 4BSST User Manual
Should your instillation conditions be constricted, then additional forced air-cooling may be necessary. Gold plated locking bryyston plugs are available from Bryston.
Balanced systems provide noise rejection from external electrical interference, so cable length can be very long 50m or longer. Balanced input Vs Single ended input: Input Sensitivity Gain Switch.
The above noise ratings represent minimum readings, actual readings may be better. The power up or turn-on of the 3B SST may be activated by remote control voltage. Also see installation section on ventilation.
The 2v setting provides an amplifier gain – 23 dB.
All SST amplifiers are convection cooled. The SST amplifier uses a magnetic-trip circuit breaker 1 to protect the amplifier.
The speaker binding posts will accept wire up to 3 gage in size. Stripped bare wire up to 3 brjston can be inserted through the hole in the binding post and held in place by tightening the post knob. Tampering by persons other than factory authorized service personnel, or failure to fully comply with Bryston operating instructions, voids the warranty.
Bryston C Series 4B SST Dimensional Drawing
It’s a community-based project which helps to repair anything. Installation see rack mounting section if applicable Ventilation. Should the breaker trip, lower or remove the amplifier input signals. Lugs should mznual gold plated. Push again and the amplifier will power-down. Additional tightening pressure can be achieved using a coin in the slots of the knob. Persistent Thermal shutdown indicates steps need to be taken to increase airflow across the channel or channels heat sink.
Do not over tighten or the binding post may become damaged.
Bryston Stereo Amplifier 4B SST User Guide |
This will ensure the amplifier is protected in future transport. Ship the amplifier only in the original packing material, as the unit is not insurable by carriers otherwise. Wiring the SST amplifier also see rear panel description Speaker wires should be as short as practical.
Banana plugs offer a quick disconnect option. For this reason do not install anything directly above it.
BRYSTON C SERIES 4B SST DIMENSIONAL DRAWING Pdf Download.
Cables should be kept as short as practical and should never be terminated with connectors that may become confused for AC power connectors. Note that copper wire is malleable and may require further tightening after the initial installation. Any amplifier that is constantly operated into clipping indicates a more powerful amplifier is needed for that application. The balanced input requires a balanced pre-amp source.
Gold plated spade lugs are available from Bryston.