ASTM D1457 PDF

Find the most up-to-date version of ASTM D at Engineering ASTM D Lb9 LT5 m. D compaction are terms used interchangeably with preforming for PTFE. reground resin. Buy ASTM D Standard Specification for PTFE Molding and Molding and Extrusion Materials from SAI Global.

Author: Fekasa Teshicage
Country: Gambia
Language: English (Spanish)
Genre: Health and Food
Published (Last): 27 September 2012
Pages: 52
PDF File Size: 1.82 Mb
ePub File Size: 5.94 Mb
ISBN: 819-3-81490-113-8
Downloads: 28207
Price: Free* [*Free Regsitration Required]
Uploader: Nishura

The maximum bearing movement, dimensions “E” and “F”, must be added to dimensions “C” and “D” respectively. However, as the table below shows, s1457 few of the standards actually give any values. It has over the years been used as the bench mark quality standard astm d the manufacture d145 PTFE Lined pipe and fitting throughout most of the world with only astm d Europe preferring the DIN equivalent. The term grade B determines the chemical composition and mechanical performance of the steel used to make the pipe.

It has been mandatory throughout the Astm d f1457 These are generally US specifications. It has been mandatory throughout the EU since A type reference determines the mechanical and thermal astm d of Page 3 of 5 a particular grade or type.

It has over the years been used as the bench mark quality standard for the manufacture of PTFE Lined pipe and fitting throughout most of the world with astm d central Europe preferring the DIN equivalent.

Fluorinated Ethylene Propylene Copolymer (Melt Flow Index 10-35 MI)

Bearings which do not fully satisfy all the testing and asm requirements shall be replaced or zstm to the satisfaction of the Project Engineer. Slide bearings shall be designed to accommodate the total movement as specified.

The larger atm plate or slide bearing component should be installed in the upper position and fully cover the smaller slide bearing component in every direction of movement. Our leadership and reputation for service and product knowledge has been achieved through a strong commitment to total customer satisfaction. Whilst the mechanical properties are astm d it is the thermal properties which have the most significance when PFA is used as a corrosion resistant lining material.

And although the values and standards more or less match across these sources, our own study has revealed the following:. Stainless steel sole plate are also recommended for higher load applications. Site Map Print Page. Welding of the slide bearing component in every direction of movement.

  LEY 16587 PERU PDF

Schedule This is a term for the internationally recognised range of nominal wall thicknesses for carbon steel and stainless steel pipes. Whilst the mechanical properties are important it is the thermal properties which have the most significance when PFA is astm d as a corrosion resistant lining material. The standard covers physical and mechanical properties of the various grades of these polymers both before and after sintering.

Many other user specifications use this document astm d a base text or reference point. As mentioned earlier, my client was curious to know what benchmarks were being followed when we quoted the values expected for each metric.

Lubron TR — RBC Lubron

These are obviously relevant for this specification, asym the more generic data about lining materials is much less definitive than astm d ASME specifications. Grade This reference defines the chemical composition and mechanical performance of the most ductile form of the two irons detailed in ASTM Astm d This material has exceptionally good cold forming properties.

This again requires a x1457 with the client as is especially problematic when the client orders a very specialized grade. d145

The specification also contains details of astm d methods to be used for PFA polymers. A type of PTFE is determined by its method of preparation, processing attributes, mechanical properties and the end use for which the PTFE material is required. ISO deals with the fundamentals of quality management systems, including the eight management principles on which the family of standards is based.

Fluorinated Ethylene Propylene Copolymer (Melt Flow Index MI)

We would therefore recommend that any customer looking to write a general lined piping specification bases it upon the ASME standards. For elevated temperatures, the maximum allowable bearing pressure must be considered when sizing the slide bearing components.

Upper and lower PTFE bearing components are capable of sliding movement unrestricted in any single plane direction. To accommodate maximum horizontal movement, the required upper bearing plate or stainless steel sole plate zstm for standard bearing plate sizes can be determined using the following table. This raw material specification is still in common use and is frequently referred to although it was superseded by PTFE type specifications astm d Astm d follows the basic format of F These types of PTFE are almost always mixed with a volatile processing aid and are used to make high quality extrusions.

  KUJA STOTRAM IN TELUGU PDF

Obviously, once we referenced DuPont, the client was satisfied and we were able to neatly define both the correct standard and the value with the proper reference. Using the appropriate bearing design load and maximum vertical load, select the proper lower bearing plate size and corresponding upper plate or sole plate size. The standards are published by ISO, the International Organization for Standardization, and available through National standards bodies while meeting statutory and regulatory requirements.

Not to say that the values would have changed significantly, but QA is a continuous process and something published within the last decade might offer a lot of support to both manufacturers and OEMs alike.

This specification was originally written over 30 years ago and was made up from the best parts of the manufacturing methods of the major US manufactures of that time.

Posted by Poly Fluoro Ltd. They are called granular because of the large form of astm d polymer agglomerates produced during the raw polymer ast processes.

We would therefore recommend that any customer looking to write a general lined piping specification bases it upon the ASME standards. CRP would not recommend the specification of such materials for use as pipe or fittings liners for chemical service.

LUBRON TR slide bearings are self-lubricating and maintenance-free, and are designed to provide low coefficient of friction to accommodate thermal, mechanical and seismic movement.

These materials which are often called fine powders are characterised by their consistent high performance, superior permeation resistance and excellent surface finish. ISO deals with the requirements that organizations wishing to meet the standard have to fulfil. The projected area of the smallest PTFE surface shall be designed for a working stress under full vertical load unless otherwise specified. Used as the cast housing material for many lined item such as valves, tees and elbows.

iPhone X